MPO6002EDU Series Oscilloscope Guide
MPO6002EDU Series OscilloscopeAt a GlanceMPO6002EDU Series Model Numbers, Bandwidths
ModelMPO6082EDUMPO6102EDUMPO6202EDU
Channels2
Bandwidth80MHz100MHz200MHz
Sampling Rate1 GSa/s (single channel), 500 MSa/s (two channels)
Memory Depth128M (single channel), 64M (two channels)
Segmented MemoryYes
Waveform GeneratorYes (3 channels, 25MHz)
Logic AnalyzerYes (16 channels, 4 channels each group)
AUX TerminalYes (Trigger out and Pass/Fail output)
LAN InterfaceYes
WiFi Yes
Touch ScreenYes
MPO6002EDU Series oscilloscope main features ? 1 GSa/s real-time sample rate.? 128M memory depth.? 256-grade color display. ? Low base noise, 500 uV/div to 10 V/div ultra-wide vertical dynamic range.? 60,000 waveforms/second update rate (dots display mode); 400,000 waveforms/second (dots display fast acquisition mode). ? Segmented acquisition function, support to capture up to 80,000 sections.? 7.0-inch WVGA (800*480) TFT LCD, with capacitive touch screen.? Trigger types: edge, pulse, video, slope, overtime, window, pattern, interval, under amp, delay, and setup/hold. ? Serial decode/trigger options for UART, LIN, CAN, IIC, SPI. Digital channels and serial decode cannot be on at the same time. ? 42 built-in measurements, and a measurement statistics display.
? Math waveforms: add, substract, multiply, divide, FFT, integrate, Differentiate, square root, expression.? Event search function.? Frequency response analyzer (FRA).? With Pass/Fail output and Trigger out function.? 5 bits digital voltmeter (DVM) and 6 bits frequecy counter.? Built-in 16 digital channels logic analyzer lets you debug mixed signal designs using analog signals and tightly correlated digital signals simultaneously.? Built-in 3 channels waveform generator with: sine, square, ramp, noise, pulse, DC, sine cardinal, exponential fall, haversine, lorentz, dual tone, gause, ECG, arbitrary. ? Standard interfaces: USB Device, USB Host, LAN, AUX port and WiFi module. ? Optional interfaces: HDMI.? Supports remote command control.
Inspect the package contents including the following items. ? MPO6002EDU Series oscilloscope. ? Power cord. ? BNC cable.? Oscilloscope probes. ? Test Leads with BNC plug and alligator clip.? BNC to BNC cable. ? Type C cables.? Digital probes. ? Mini test hooks.
Getting StartedConnect Probes to the Oscilloscope 1 Connect the oscilloscope probe to an oscilloscope channel BNC connector.2 Connect the probe’s retractable hook tip to the point of the interest on the circuit or device under test. Be sure to connect the probe ground lead to a ground point on the circuit. CAUTION When measuring voltages over 80V, use a 10:1 probe. CAUTION Do not float the oscilloscope chassis
Edited by WisdomAugust at 2020-7-7 09:52
Defeating the ground connection and floating the oscilloscope chassis will probably result in inaccurate measurements and may also cause equipment damage. The probe ground lead is connected to the oscilloscope chassis and the ground wire in the power cord. If you need to measure between two live points, use a differential probe with a sufficient dynamic range. WARNING Do not negate the protective action of the ground connection to the oscilloscope. The oscilloscope must remain grounded through its power cord. Defeating the ground create an electric shock hazard.
Edited by WisdomAugust at 2020-7-7 09:51
Input a Waveform The first signal to input to the oscilloscope is the probe comp (2Vpp@1KHz square) signal. This signal is used for compensating probes. 1 Connect an oscilloscope probe from channel 1 to the probe comp terminal on the front panel.2 Connect the probe’s ground lead to the ground terminal (next to the probe comp terminal).
Edited by WisdomAugust at 2020-7-10 08:19
Recall the Default Oscilloscope Setup Press on the front panel. The default setup restores the oscilloscope's default settings. This places the oscilloscope in a known operating condition. The major default settings are:l Horizontal - Normal mode, 100ns/div scale, 0s delay, center time reference. l Vertical (Analog) -All channels on, 5V/div scale, DC coupling, 0V position. l Trigger - Edge trigger, Auto trigger mode, 0V level, channel 1 source, DC coupling, rising edge slope, 20ns holdoff time. l Display - Persistence off, 50% grid intensity, 80% waveform intensity, 80% screen brightness. l Other - Acquire mode normal, to Run, cursors, and measurements off. l Labels - All custom labels that you have created are erased, and all channel labels will be set to their original names.