MPO6002EDU Series Oscilloscope Guide

WisdomAugust

Run/Stop Key help information

Press the Run/Stop key to stop and start waveform acquisition.

When the key in green (run status), you can resume continuous acquisition after a single sequence acquisition.

When the key in red (stop status), you can use the vertical and horizontal knobs to pan and zoom the stored

waveforms (last trigger acquisition).

Single Key help information

Press the Single key to acquire a single waveform trace.

The key will remain orange until the oscilloscope is triggered. After the trigger event, the waveform is displayed

and triggering is disabled until re-armed by pressing the Single key again.

WisdomAugust

Force Trig Key help information

Press and immediately release the Force Trig key to force the scope to trigger and display the signal at the time

it was triggered.

In Auto trigger mode, the trigger will be forced if the specified conditions are not met.

In Normal trigger mode, the trigger will never be forced and a trigger will only occur if the specified conditions

are met.

Press and hold the Force Trig key to display history waveform menu.

WisdomAugust

Trig Menu Key -> Mode Softkey help information

Press this softkey to toggle the trigger mode between Auto and Normal.

* Auto mode - it causes the scope to draw a waveform even no trigger detected.

* Normal mode - the scope only displays waveforms when the input signal meets the set trigger condition.

Trig Menu Key -> 50% Softkey help information

This softkey sets the trigger level of displayed analog channel trigger source to 50% value of the waveform.

Trig Menu Key -> Holdoff Softkey help information

Press this softkey and turn the V0 knob to adjust the trigger holdoff time during which the scope cannot trigger.

Use Holdoff to create a stable display of complex waveforms.

WisdomAugust

Trig Menu Key -> Type -> IIC -> When Softkey help information

Press this softkey to select the desired trigger condition.

* Start - triggers when serial data transitions from high to low while serial clock is high level.

* Stop -  triggers when serial data transitions from low to high level while serial clock is high.

* No Ack - triggers when a write data byte or the selected address field is not acknowledged.

* Address - triggers on the specified address value.

* Restart - triggers when another start condition occurs before a stop condition.

* Address & Data - triggers on a combination of both specified address and data.

Trig Menu Key -> Type -> IIC -> Address Softkey help information

Press this softkey and use the V0 knob to set a address value.

WisdomAugust

Trig Menu Key -> Type -> SPI -> Data Bit Softkey help information

Press this softkey and turn the V0 knob to select the number of bits in a word.

Trig Menu Key -> Type -> IIC -> Address Size Softkey help information

Press this softkey to set the scope to trigger on a 7- bit address read/write frame or a 10-bit address write frame.

Trig Menu Key -> Type -> IIC -> SCL Softkey help information

This softkey sets the source of the serial clock signal to any analog or digital channel input.

Trig Menu Key -> Type -> IIC -> SDA Softkey help information

Press this softkey to set the source of the serial data signal to any analog or digital channel input.

WisdomAugust

Trig Menu Key -> Type -> SPI -> SCL Softkey help information

This softkey sets the source of the serial clock signal to any analog or digital channel.

Trig Menu Key -> Type -> SPI -> Slope Softkey help information

You can use this Slope softkey to select the clock edge between rising and falling.

Trig Menu Key -> Type -> SPI -> SDA Softkey help information

Press this softkey to set the source of the serial data signal to any analog or digital channel.

Trig Menu Key -> Type -> SPI -> Timeout Softkey help information

The scope searches for the data on which to trigger after a specified period of time during which

the clock signal stays in the idle state.

Press this softkey and rotate the V0 knob to adjust the Timeout. Time setting range: 8ns - 10s.

Trig Menu Key -> Type -> SPI -> Data Length Softkey help information

This softkey sets the number of bits in the serial data string from 4 bits to 32 bits.

WisdomAugust

Trig Menu Key -> Type -> CAN -> When Softkey help information

Press this softkey to select the desired trigger condition.

* Start or Frame -  triggers at the start of a frame.

* Remote Frame ID - triggers on remote frames with the preset identifier.

* Data Frame ID - triggers on data frames matching

the preset identifier.

* Frame ID - triggers on remote or data frames matching the preset identifier.

* Data Frame ID & Data - triggers on data frames

matching the preset identifier and data.

* Error Frame - triggers on the error frame.

* All Errors - triggers on any form error or active error.

* Ack Error - triggers on the recessive acknowledge bit.

* Overload Frame - triggers on CAN overload frames.

WisdomAugust

Trig Menu Key -> Type -> LIN/CAN -> Identifier Softkey help information

Press this softkey and use the V0 knob to setup the identifier value.

Trig Menu Key -> Type -> LIN/CAN/IIC -> Data 1 Softkey help information

Press this softkey and turn the V0 knob to set the data value for Data 1.

Trig Menu Key -> Type -> LIN/CAN/IIC -> Data 2 Softkey help information

Press this softkey and turn the V0 knob to set the data value for Data 2.

Trig Menu Key -> Type -> LIN/CAN/IIC -> Data 3 Softkey help information

Press this softkey and turn the V0 knob to set the data value for Data 3.

Trig Menu Key -> Type -> LIN/CAN/IIC -> Data 4 Softkey help information

Press this softkey and turn the V0 knob to set the data value for Data 4.

WisdomAugust

Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> Event Table Softkey help information

Press this softkey to open the Event Table Menu and display the Decoded Packet Data Tabular on the screen.

Trig Menu Key -> Type -> LIN -> When Softkey help information

Press this softkey to select the desired trigger condition.

* Break Field -  the scope triggers on the edge at the Sync Break exit of the LIN single-wire bus signal that marks

the beginning of the message frame.

* Sync Field -  the scope triggers on the last bit of the sync field.

* ID Field -  the scope triggers on the last bit of the identifier field.

* Sync Error - triggers when the synchronous data is not 0x55.

* Identifier - triggers on a specific identifier.

* ID & Data - triggers on a combination of both identifier and data.

WisdomAugust

Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> Idle Level Softkey help information

Set idle level to high or low to match the state of the device under test when at idle.

Trig Menu Key -> Type -> UART -> Polarity Softkey help information

According to the device under test to select the parity from odd, even, or none.

Trig Menu Key -> Type -> UART -> Data Bits Softkey help information

This softkey sets the number of bits to 5, 6, 7, or 8bits in the UART words to match the device under test.

Trig Menu Key -> Type -> UART -> Data Softkey help information

This softkey sets the trigger data ( only available when the trigger type is data).

Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> Decode Softkey help information

Press this softkey to enable or disable the decode display.

Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> Position Softkey help information

If the decode turned on, press this softkey and use the V0 knob to move the decode label up and down on the display.