Electronic Engineer Discuss

Title: How to do mainboard programming via USB? [Print this page]

Author: WisdomAugust Time: 2020-4-15 08:54
Title: How to do mainboard programming via USB?

Install and configure tool SecureCRT

Unzip “SecureCRT.rar” in the file.

Double click “SecureCRT.exe”

[attach]3493[/attach]

Click “OK”.

Author: WisdomAugust Time: 2020-4-16 08:26

Select “Yes”.

[attach]3495[/attach]

Configure as follows:

[attach]3496[/attach]

Author: WisdomAugust Time: 2020-4-17 08:10

According to your device, select the “com” in Port Item, click “Connect”.

[attach]3512[/attach]

If this interface appears, it means the connection is successful.

[attach]3513[/attach]

Author: WisdomAugust Time: 2020-5-6 08:08
Check

1. Connect the device serial port (J801) to PC RS232 port or USB port via RS232 to TTL module or

USB to TTL module.

[attach]3555[/attach]

[attach]3556[/attach]

[attach]3557[/attach]

Author: WisdomAugust Time: 2020-5-7 08:07

2. Power on. If there isn't any in the serial interface, execute 2.3~2.6. If there will be some terminal

output in the serial interface, please send the output content to the customer service personnel to

get the subsequent operation instructions.

Author: WisdomAugust Time: 2020-5-7 08:07
Edited by WisdomAugust at 2020-5-8 09:41

Install hjtag Tools and Program ***.bin

Add equipment giveio

Unzip GIVEIO.rar file in programming tools. Copy the content in GIVIO folder into driver path of system partition:

C:\WINDOWS\system32\drivers

[attach]3563[/attach]

Author: WisdomAugust Time: 2020-5-9 08:56

Open Control Panel of the computer.

Select the “Add Hardware” option.

Select “Next”.

Select “yes”, click “next”.

Select “Add new hardware equipment”, click “next”.

Select “Install manual list choosing hardware”, click “next”.

Select “Port COM and IPT”, click “next”.

Select “Install from disk”.

Click “Review”.

Select unzipped GIVIEIO.inf file from the dialog box and open it.

Click “Confirm”.

Click “Next”.

Click “Finish”.

Author: WisdomAugust Time: 2020-5-11 08:54
Install and configure hjtag software
Unzip H-JTAG V3.0 RELEASE.rar file.[attach]3564[/attach]

Double click H-JTAG V3.0 RELEASE.EXE in the unzipped folder.[attach]3565[/attach]

Author: WisdomAugust Time: 2020-5-12 10:12
Click “Next”.[attach]3566[/attach]

Select “I agree with….” option, click “Next”.
[attach]3567[/attach]

Select destination folder of installation, click “Next”.

[attach]3568[/attach]

Author: WisdomAugust Time: 2020-5-13 09:44

Waiting for installation.

[attach]3576[/attach]

Click “Finish” to finish the installation, there would be a shortcut of software produced on the desktop.

[attach]3577[/attach]

Author: WisdomAugust Time: 2020-5-15 08:23

Double click H-JTAG icon on the desktop, select some information that appears.

[attach]3578[/attach]

Connect mainboard (J901) and computer by parallel port wire and parallel port pinboard.

Power on.

[attach]3579[/attach]

[attach]3580[/attach]

Author: WisdomAugust Time: 2020-5-19 08:11

Select “Settings” from the menu bar.

[attach]3585[/attach]

Select USB/LPTSetting

[attach]3586[/attach]

Author: WisdomAugust Time: 2020-5-20 08:13
Edited by WisdomAugust at 2020-5-21 08:35

Select LPT JTAG Setting.

[attach]3588[/attach]

[attach]3589[/attach]

According to your pinboard, select to directly click “OK” or select “User Defined”.

If select “User Defined”, please refer to the below configuration.

[attach]3598[/attach]

Author: WisdomAugust Time: 2020-5-21 08:37
2.3.3 Program ***.bin

Connect mainboard (J901) and computer by parallel port wire and parallel port pinboard. Power on.

[attach]3599[/attach]

[attach]3600[/attach]

Author: WisdomAugust Time: 2020-5-22 09:45

1. Open software hjtag, click the Magnifier in the software interface and detect the mainboard

2. After detection, the model of CPU would be shown as blue in the software interface.

3. Click the “F” [attach]3601[/attach] icon in the software interface.

[attach]3602[/attach]

Click “Load”

Author: WisdomAugust Time: 2020-5-23 08:06

Select the file 2416.hfc in the programming file.

[attach]3603[/attach]

Click “4 Programming” on the left side of the panel.

[attach]3604[/attach]

Author: WisdomAugust Time: 2020-6-1 08:35

Click “Check”, the CPU and flash model of mainboard would be shown.

[attach]3643[/attach]

Click ellipsis button, select image “whu-boot_5102p3nand_64MB_TFT70_V1.1.bin” in the image

file corresponding with the mainboard.

[attach]3644[/attach]

Author: WisdomAugust Time: 2020-6-2 08:46

Click “Program” until finishing programming.

[attach]3650[/attach]

The connection between the mainboard of parallel port and computer can be switched off only after

the finish of programming.

Author: WisdomAugust Time: 2020-6-3 08:09
2.4 Install EmbedSkyDownLoadTool

Unzip EmbedSkyDownLoadTool_V1.0.rar file.

[attach]3651[/attach]

Double click the icon to install.

Click “Next”.

Select the path of file installation, click “next”.

Click “Install”.

Click “Finish”. If it warns that “.net4.0” is required to install at the beginning of the installation,

please unzip “dotNetFx40_Full_x86_x64.rar” in the programming folder. Double click and press enter key to install it.

Author: WisdomAugust Time: 2020-6-4 09:23
2.5 Program others2.5.1 Connect

Connect the mainboard and computer by serial port wire. Open software SecureCRT. Connect the correct “com” port.

Connect the computer and mainboard by USB cable.

[attach]3655[/attach]

Author: WisdomAugust Time: 2020-6-4 09:24
2.5 Program others2.5.1 Connect

Connect the mainboard and computer by serial port wire. Open software SecureCRT. Connect the correct “com” port.

Connect the computer and mainboard by USB cable.

[attach]3656[/attach]

Author: WisdomAugust Time: 2020-6-5 08:20

Connect your scope(J801) to PC serial interface via RS232 to TTL module or USB to TTL module.

[attach]3657[/attach]

[attach]3658[/attach]

[attach]3659[/attach]

Author: WisdomAugust Time: 2020-6-6 08:08
2.5.2 Install USB download driver

Restart it and import several “blank” fastly and immediately, the interface would be shown as below.

[attach]3663[/attach]

Tap “2”, the unknown device will be found and waiting to be installed.

Select the USB Download Driver folder to install the driver.

[attach]3664[/attach]

Author: WisdomAugust Time: 2020-6-8 08:30
2.5.3 Download wh3 zImage_5102P3 into mainboard

After installing the driver successfully, tap “3”, click “enter”

[attach]3666[/attach]

Author: WisdomAugust Time: 2020-6-9 08:08

Open EmbedSkyDownLoadTool, select USB->UBOOT->select file

[attach]3674[/attach]

Select wh3 zImage_5102P3

[attach]3675[/attach]

Then review software SecureCRT

When this statement “Enter your selection: ” appears, that means wh3 zImage_5102P3 programming is finished.

Author: WisdomAugust Time: 2020-6-10 09:10
2.5.4 Downloadwh5 root_dso5102p3.ubi

Select “5”, click “enter”

[attach]3676[/attach]

Author: WisdomAugust Time: 2020-6-11 09:27

Select wh5 root_dso5102p3.ubi

[attach]3685[/attach]

[attach]3684[/attach]

2.6 Power off and restart the device

Welcome to Electronic Engineer Discuss (https://eediscuss.com/)