MPO6002EDU Series Oscilloscope Guide

WisdomAugust · Post time 2021-4-20 08:20:11

Trig Menu Key -> Type -> UART/LIN/CAN -> Source Softkey help information

Press this softkey and turn the V0 knob to select the trigger source from analog or digital channels input.

Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> Baud Rate Softkey help information

This softkey selects a baud rate of data transmission to match the signal in the device under test.

If the desired baud rate is not listed, select User Defined.

Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> User Baud Softkey help information

When User Defined selected on the Baud Rate softkey, press User Baud softkey and turn the V0 knob to

set the desired baud rate at a small step of 1 bps.

Trig Menu Key -> Type -> UART -> When Softkey help information

Press this softkey to select the desired trigger condition.

* Start - the scope triggers on the start frame position.

* Stop - the scope triggers on the stop frame position. The trigger will occur on the first stop bit whether the

device under test uses 1, 1.5, or 2 stop bits.

* Data - triggers on the last bit of the specified data bits.

* Parity Error - triggers on a parity error based on the preset parity on the Parity softkey.

* Error - triggers when an error occurs by checking the start bit and stop bit.

WisdomAugust · Post time 2021-4-19 11:27:43

Trig Menu Key -> Type -> Setup/Hold -> Slope Softkey help information

This softkey sets the active edge of the clock signal to rising or falling.

Trig Menu Key -> Type -> Setup/Hold -> Type Softkey help information

Press this softkey to toggle the time type between setup and hold.

Trig Menu Key -> Type -> Setup/Hold -> When Softkey help information

The scope triggers when the setup time or hold time is smaller than the preset time.

Trig Menu Key -> Type -> Setup/Hold -> Width Softkey help information

Press this softkey and use the V0 knob to preset the time. Settings range: 8ns - 10s.

WisdomAugust · Post time 2021-4-16 09:39:04

Trig Menu Key -> Type -> Setup/Hold -> Source Softkey help information

Selects data signal source of the setup and hold trigger from analog channels.

Trig Menu Key -> Type -> Setup/Hold -> SDA Softkey help information

Selects data signal source of the setup and hold trigger from analog channels.

Trig Menu Key -> Type -> Setup/Hold -> Data Type Softkey help information

Press this softkey to toggle the data signal's effective pattern between high level and low level.

Trig Menu Key -> Type -> Setup/Hold -> SCL Softkey help information

Sets clock signal source of the setup and hold trigger to any analog or digital channel input.

WisdomAugust · Post time 2021-4-15 08:37:56

Trig Menu Key -> Type -> Delay -> Slope 2 Softkey help information

Set the trigger slope 2 for the selected trigger source 1 to rising or falling logic.

Trig Menu Key -> Type -> Delay -> When Softkey help information

Press this softkey to select the delay type.

The scope can be triggered when time differences between signals are:

* equal to (=) the specified time.

* not equal to (≠) the specified time.

* greater than (>) the specified time.

* less than (<) the specified time.

Trig Menu Key -> Type -> Delay -> Width Softkey help information

Press this softkey and use the V0 knob to preset the time. Settings range: 20ns - 10s.

WisdomAugust · Post time 2021-4-14 08:22:18

Trig Menu Key -> Type -> Delay -> Source 1 Softkey help information

Press this softkey to set edge trigger source 1 to any analog or digital channel.

Trig Menu Key -> Type -> Delay -> Slope 1 Softkey help information

Set the trigger slope 1 for the selected trigger source 1 to rising or falling logic.

Trig Menu Key -> Type -> Delay -> Source 2 Softkey help information

Press this softkey to set edge trigger source 2 to any analog or digital channel.

WisdomAugust · Post time 2021-4-13 10:07:13

Edited by WisdomAugust at 2021-4-13 10:08

Trig Menu Key -> Type -> Runt -> Source Softkey help information

Sets the runt trigger source to any analog channel input.

Trig Menu Key -> Type -> Runt -> Polarity Softkey help information

Press this softkey to change the runt polarity settings, you can trigger on positive or negative polarity.

Trig Menu Key -> Type -> Runt -> When Softkey help information

This qualifier softkey lets you trigger on a runt pulse whose times are:

* equal to (=) the specified time.

* not equal to (≠) the specified time.

* greater than (>) the specified time.

* less than (<) the specified time.

Trig Menu Key -> Type -> Runt -> Width Softkey help information

Press this softkey and turn the V0 knob to adjust the runt width. Setting range: 20ns - 10s.

Trig Menu Key -> Type -> Runt -> Level Softkey help information

Press this softkey to select the threshold levels: Level A, Level B, or both of them. Then, turn the V0

knob to adjust.

WisdomAugust · Post time 2021-4-12 08:03:20

Trig Menu Key -> Type -> Interval -> Source Softkey help information

This softkey lets you can set interval trigger source to any analog or digital channel input.

Trig Menu Key -> Type -> Interval -> Slope Softkey help information

Press this softkey to set the trigger slope to rising or falling.

Trig Menu Key -> Type -> Interval -> When Softkey help information

Set the scope to trigger on a periodical signal with interval time that is:

* equal to (=) the specified time.

* not equal to (≠) the specified time.

* greater than (>) the specified time.

* less than (<) the specified time.

Trig Menu Key -> Type -> Interval -> Time Softkey help information

Press this softkey and rotate the V0 knob to adjust the interval time.

WisdomAugust · Post time 2021-4-10 08:22:03

Trig Menu Key -> Type -> Pattern -> Source Softkey help information

This softkey selects pattern trigger source from analog or digital channels.

Trig Menu Key -> Type -> Pattern -> Code Softkey help information

Press this softkey to set the value of the selected channel.

* X - Don't care

* 1 - One

* 0 – Zero

WisdomAugust · Post time 2021-4-9 10:03:46

Trig Menu Key -> Type -> Timeout -> Source Softkey help information

This softkey sets the timeout trigger source to any analog or digital channel input.

Trig Menu Key -> Type -> Timeout -> Polarity Softkey help information

This softkey selects positive or negative polarity.

Trig Menu Key -> Type -> Timeout -> Period Softkey help information

Press this softkey and turn the V0 knob to adjust the timeout period.

Trig Menu Key -> Type -> Window -> Source Softkey help information

Press this softkey to select window trigger source from analog channels.

Trig Menu Key -> Type -> Window -> Level Softkey help information

This softkey lets you set a 'window' by adjusting voltage levels. Window trigger detects the moment when the

waveform enters or leaves set window voltage range.

WisdomAugust · Post time 2021-4-8 10:10:27

Trig Menu Key -> Type -> Slope -> When Softkey help information

Set the scope to trigger on rising or falling slope condition that is:

* equal to (=) the specified time.

* not equal to (≠) the specified time.

* greater than (>) the specified time.

* less than (<) the specified time.

Trig Menu Key -> Type -> Slope -> Time Softkey help information

Press this softkey and rotate the V0 knob to adjust the slope time. Time setting range: 20ns - 10s.