MPO6002EDU Series Oscilloscope Guide

WisdomAugust

Wave Gen Key -> Waveform -> Pulse -> Leading/Trailing Softkey help information

Press this softkey to toggle between Leading edge (Fine) and Trailing edge (Fine) adjustment, and use

the V0 knob to adjust the edge times.

The edge times set the transition times for the leading and trailing edges of the pulse.

The device will adjust the edge time to accommodate the specified pulse width.

Wave Gen Key -> Waveform -> Arb 1/Arb 2/Arb 3/Arb 4 -> Recall Softkey help information

Press this softkey to display a screen-based file list if a USB storage device detected.

Turn the V0 knob to select an arbitrary waveform data file, press the V0 knob to load the arbitrary

waveform to the oscilloscope.

Wave Gen Key -> Source Softkey help information

Select the channel of the waveform generator.

WisdomAugust

Wave Gen Key -> Waveform -> Square -> Duty Softkey help information

Press this softkey to toggle between Duty and Duty Fine adjustment, and use the V0 knob to adjust the

duty cycle of the square waveform output. Settings range: 2% - 98%.

Wave Gen Key -> Waveform -> Ramp -> Symmetry Softkey help information

Press this softkey to toggle between Symmetry and Symmetry Fine adjustment, and use the V0 knob

to adjust the symmetry of the ramp waveform output. Symmetry applies optional symmetry modifications

to the wave shape.

Wave Gen Key -> Waveform -> Pulse -> Width Softkey help information

Press this softkey to toggle between Width and Width Fine adjustment, and use the V0 knob to adjust

the width of the pulse waveform output.

WisdomAugust

Wave Gen Key help information

Press the WaveGen key to open the Waveform Generator Menu (if the scope with built-in waveform generator).

*Select channels of the waveform generator.

*Turn on or off output on the front panel's Gen Out BNC.

*Set up the waveform generator's wave type, frequency, amplitude, offset, phase, impedance, modulation, and burst.

Wave Gen Key -> Waveform Softkey help information

Select the waveform generator output by pressing this softkey or turning the V0 knob.

The current waveforms can be output with Sine, Square, Ramp, Noise, Pulse, DC, Sinc, Exponential Fall,

Haversine, Lorentz, Dual Tone, Gauss, ECG, and Arbitrary waveforms.

WisdomAugust

Meas Key -> Gate Softkey help information

Press this softkey to enter the Gate Menu.

Meas Key -> Gate -> Gate On/Off Softkey help information

Press this softkey to turn on or off the gate measure function.

Meas Key -> Gate -> Gate On -> Cursor A Softkey help information

Press this softkey and use the V0 knob to adjust Cursor A position.

Meas Key -> Gate -> Gate On -> Cursor B Softkey help information

Press this softkey and use the V0 knob to adjust Cursor B position.

Meas Key -> Gate -> Gate On -> Cursor A-B Softkey help information

Press this softkey and use the V0 knob to adjust Cursor A and Cursor B positions together.

Meas Key -> Gate -> Return Softkey help information

Press this softkey to return to the previous menu.

WisdomAugust

Meas Key -> Settings Softkey help information

Press this softkey to display the Settings Menu to set up additional parameters for the selected measurement.

Meas Key -> Settings -> Type Softkey help information

Choose Delay (or Phase if available) as the selected measurement.

Meas Key -> Settings -> Source A Softkey help information

Press Source A softkey to select an analog channel for Delay (or Phase if available) measurement.

Meas Key -> Settings -> Source B Softkey help information

Press Source B softkey to select an analog channel for Delay (or Phase if available) measurement.

Meas Key -> Settings -> Return Softkey help information

Press this softkey to return to the previous menu.

WisdomAugust

Meas Key -> All Measure Softkey help information

Turn on or off all measure function.

Meas Key -> Statistics Softkey help information

Turn on or off measurement statistics for active measurements.

The statistics display information:

* Measurement name

* Currently measured value

* The average

* The maximum measured value

* The minimum measured value

* The standard deviation (RMSE)

* The number of times the measurement has been made (count)

Meas Key -> Clear All Softkey help information

Press this softkey to remove all measurements from the display.

WisdomAugust

Meas Key -> DVM Softkey help information

Press this softkey to open the Digital Voltmeter (DVM) Menu.

Meas Key -> DVM -> Enable Softkey help information

Enable or disable digital voltmeter.

Meas Key -> DVM -> Source Softkey help information

Press this softkey to select an analog channel waveform source for which you want to measure.

Meas Key -> DVM -> Type Softkey help information

Switch the digital voltmeter measurement type among DC RMS, AC RMS, and DC.

Meas Key -> DVM -> Return Softkey help information

Press this softkey to return to the previous menu.

WisdomAugust

Meas Key help information

When open the Measurements Menu by pressing the Meas key, you can:

*Make automatic measurements (up to 42 measurement parameters).

*Turn on or off statistic measurements.

*Enable or disable digital voltmeter.

Meas Key -> Source Softkey help information

Select the channel, math, or reference waveform as the source to make measurements.

Meas Key -> Type Softkey help information

Press this softkey to display the screen-based menu to select fully-automated measurements

like frequency, period, rise/fall time, etc.

WisdomAugust

Cursors Key -> Mode Track -> Source A Softkey help information

Select the analog channel or math as the source A to measure their waveform values.

Cursors Key -> Mode Track -> Source B Softkey help information

Select the analog channel or math as the source B to measure their waveform values.

Cursors Key -> Mode Track -> Cursors Softkey help information

Press this softkey to make the selection of the cursor(s), and turn the V0 knob to adjust them. When you

turn the V0 knob, as the X cursor moves, the corresponding Y cursor follows the waveform assigned to

the X source.

The AX cursor (long-dashed-vertical line) and BX cursor (short-dashed vertical line) adjust horizontally

and indicate time relative to the trigger point for all sources except math FFT (frequency is indicated).

AXBX Press this softkey to adjust the AX and BX cursors together by turning the V0 knob. The BX - AX

value will remain the same since the cursors adjust together.

WisdomAugust

Cursors Key -> Mode Manual -> Cursors Softkey help information

Press this softkey to make the selection of the cursor(s), and turn the V0 knob to adjust them.

The AX cursor (long-dashed-vertical line) and BX cursor (short-dashed vertical line) adjust

horizontally and indicate time relative to the trigger point for all sources except math FFT

(frequency is indicated).

AXBX Press this softkey to adjust the AX and BX cursors together by turning the V0 knob.

The BX - AX value will remain the same since the cursors adjust together.

You can adjust the X cursors together to check for pulse width variations in a pulse train.

The AY cursor (long-dashed horizontal line) and BY cursor (short-dashed horizontal line)

adjust vertically and indicate values relative to the waveform's ground point, except math

FFT where the values are relative to 0 dB.

AYBY Press this softkey to adjust the AY and BYcursors together by turning the V0 knob.

The BY - AY value will remain the same since the cursors adjust together.