MPO6002EDU Series Oscilloscope Guide

WisdomAugust · Post time 2021-1-5 08:37:06

Edited by WisdomAugust at 2021-1-5 08:38

Utility Key -> System Set -> Network -> Gateway Softkey help information

Configure Gateway.

Utility Key -> System Set -> Network -> DNS Softkey help information

Configure DNS (Domain Name System).

Utility Key -> System Set -> Network -> Confirm Softkey help information

Confirm your settings of the network menu page two.

Utility Key -> System Set -> Network -> Hotspot Softkey help information

Press this softkey to enable the Hotspot Settings. The scope will automatically search for available hot spots nearby.

And SSID and PSK become active to be set.

Utility Key -> System Set -> Network -> Scan Result Softkey help information

Display searched nearby Wi-Fi hotspots.

Utility Key -> System Set -> Network -> SSID Softkey help information

Configure SSID (Service Set Identifier).

Utility Key -> System Set -> Network -> PSK Softkey help information

Configure PSK (Pre Shared Key).

Utility Key -> System Set -> Network -> Confirm Softkey help information

Confirm your settings of the network menu page three.

WisdomAugust · Post time 2021-1-4 09:39:12

Edited by WisdomAugust at 2021-1-4 09:40

Utility Key -> System Set -> Network -> Network Softkey help information

Toggle the network type between eth0 and wlan0.

Utility Key -> System Set -> Network -> Status On/Off Softkey help information

Turn on or off the network status.

Utility Key -> System Set -> Network -> DHCP On/Off Softkey help information

Turn on or off DHCP (Dynamic Host Configuration Protocol).

Utility Key -> System Set -> Network -> Auto IP On/Off Softkey help information

Enable or disable the Auto IP.

Utility Key -> System Set -> Network -> Confirm Softkey help information

Confirm your settings of the network menu page one.

Utility Key -> System Set -> Network -> IP Add Softkey help information

Configure the IP address.

Utility Key -> System Set -> Network -> Subnet Mask Softkey help information

Configure the IP Subnet Mask.

WisdomAugust · Post time 2020-12-15 08:27:55

Utility Key -> Pass/Fail -> Output to DDS Softkey help information

When turning on the output to DDS, the scope is able to output a negative pulse train from the Gen Out terminal.

Utility Key -> Pass/Fail -> Return Softkey help information

Press this softkey to return to the previous menu.

Utility Key -> System Set Softkey help information

This key opens the System Setup Menu where you can turn on or off the sound, set network, edit time and date, and perform touch panel calibration.

Utility Key -> System Set -> Sound Softkey help information

Turn on or off the sound of pressing keys.

Utility Key -> System Set -> Network Softkey help information

Press this softkey to open the Network Setup Menu.

WisdomAugust · Post time 2020-12-14 10:34:32

Utility Key -> Pass/Fail -> Message On/Off Softkey help information

To open or close the time information for the waveform pass/fail.

Utility Key -> Pass/Fail -> Stop On Output Softkey help information

Stop sweep when the first input waveform does not conform to the mask.

Utility Key -> Pass/Fail -> Output On/Off Softkey help information

When turning off, the scope enters Stop state if output exists.

When turning on, the scope continues to run if the output exists.

Note that this function is available when the scope with an AUX terminal.

Utility Key -> Pass/Fail -> Mode Softkey help information

Select the expected condition to output.

Pass - Output a negative pulse train when the test is passed.

Fail - Output a negative pulse train when the test is failed.

Pass Ring - Ringing, and output a negative pulse train when the test is passed.

Fail Ring - Ringing, and output a negative pulse train when the test is failed.

Note that this function is available when the scope with an AUX terminal.

WisdomAugust · Post time 2020-12-11 08:11:27

Edited by WisdomAugust at 2020-12-11 08:12

Utility Key -> Pass/Fail -> Mask -> Save -> Save To Softkey help information

Press this softkey to select a storage location for the mask.

Utility Key -> Pass/Fail -> Mask -> Save -> Save Softkey help information

Press this softkey you can save masks to the scope's internal memory.

Utility Key -> Pass/Fail -> Mask -> Save -> Recall Softkey help information

Press this softkey to recall a mask from internal memory.

Utility Key -> Pass/Fail -> Mask -> Save -> Return Softkey help information

Press this softkey to return to the previous menu.

Utility Key -> Pass/Fail -> Mask -> Return Softkey help information

Press this softkey to return to the previous menu.

WisdomAugust · Post time 2020-12-10 08:20:53

Utility Key -> Pass/Fail -> Mask -> Vertical Softkey help information

Press this key and rotate V0 knob to adjust the vertical clearance range of mask.

Utility Key -> Pass/Fail -> Mask -> Horizontal Softkey help information

Press this key and rotate V0 knob to adjust the horizontal tolerance range of mask.

Utility Key -> Pass/Fail -> Mask -> Create Softkey help information

Press this softkey to create a mask.

Utility Key -> Pass/Fail -> Mask -> Save Softkey help information

Press this softkey to display the Save Mask Menu.

WisdomAugust · Post time 2020-12-9 08:25:34

Utility Key -> Pass/Fail Softkey help information

Open the Pass/Fail Menu.

Utility Key -> Pass/Fail -> Enable Test Softkey help information

Turn on or off the Pass/Fail function.

Utility Key -> Pass/Fail -> Source Softkey help information

Select a signal input channel from which to create the mask.

Utility Key -> Pass/Fail -> Mask Softkey help information

This key opens the Mask Setup Menu.

WisdomAugust · Post time 2020-12-8 08:10:35

Edited by WisdomAugust at 2020-12-8 08:11

Utility Key -> System Info Softkey help information

Press the System Info key to review the information about the scope like model number, serial number,

software version, firmware version, and the FPGA version.

Utility Key -> Update Softkey help information

Press the Update softkey to enter the Firmware Update Menu.

Utility Key -> Update -> Update Firmware Softkey help information

Press this softkey to display a screen-based file list if a USB storage device with an update program under

the root directory detected.

Utility Key -> Update -> Press To Update Softkey help information

When the firmware file selected by using the V0 knob, press this softkey to upgrade the scope firmware.

Utility Key -> Update -> Return Softkey help information

Press this softkey to return to the previous menu.

WisdomAugust · Post time 2020-12-7 08:27:01

Utility Key -> LA -> Source Softkey help information

Press this softkey and turn V0 knob to select a group of digital channels to display.

Note that each group of digital channel includes 4 digital channels.

Utility Key -> LA -> Type Softkey help information

Press this softkey and use V0 knob to change the logic threshold for digital channels.

Utility Key -> LA -> Threshold Softkey help information

If the Type softkey is set to User, press the Threshold softkey and turn the V0 knob to set the logic threshold.

WisdomAugust · Post time 2020-12-5 08:25:46

Edited by WisdomAugust at 2020-12-5 08:26

Utility Key -> LA Softkey help information

Open the Logic Analyzer Menu when a logic probe is connected.

It's unusable if no logic probe has been found.

Utility Key -> LA -> Enable Softkey help information

Switch a group of digital channels on or off.

When 4 analog channels (oscilloscope channels) are all turned on, the digital channels (logic analyzer channels) are not usable.

When 3 analog channels turn on, 1 group of digital channels (including 4 digital channels) is usable.

When 2 analog channels turn on, 2 groups of digital channels are usable.

When 1 analog channel turns on, 3 groups of digital channels are usable.

When all the analog channel turns off, 4 groups of digital channels are usable.