MPO6002EDU Series Oscilloscope Guide

WisdomAugust

2 If you want to return to the oscilloscope settings that existed before, press Cancel.

3 If you want to display multi-period waveforms, press Multi-Period to autoscale.

4 If you want to show one-period waveform only, press Single-Period to autoscale.

5 If you only want to review specific active channels after pressing AutoScale, press Source to select

All Channels or Only Displayed Channels.

6 If you want to enable the auto range to automatically setups the oscilloscope to best display the input

signal whenever you change the volt/div or time/div, press AutoRange.

WisdomAugust

2 If you want to return to the oscilloscope settings that existed before, press Cancel.

3 If you want to display multi period waveforms, press Multi-Period to autoscale.

4 If you want to show one period waveform only, press Single-Period to autoscale.

5 If you only want to review specific active channels after pressing AutoScale, press Source to select

All Channels or Only Displayed Channels.

6 If you want to enable autorange to automatically setups the oscilloscope to best display the input signal

whenever you change the volt/div or time/div, press AutoRange.

WisdomAugust

Use Autoscale

Use [Auto Scale] to automatically configure the oscilloscope to best display the input signals.

1 Press [Auto Scale].

You should see a waveform on the oscilloscope's display similar to this:

WisdomAugust

Recall the Default Oscilloscope Setup

Press [Default] on the front panel.

The default setup restores the oscilloscope's default settings. This places the oscilloscope in a known

operating condition.

The major default settings are:

l Horizontal - Normal mode, 100ns/div scale, 0s delay, center time reference.

l Vertical (Analog) -All channels on, 5V/div scale, DC coupling, 0V position.

l Trigger - Edge trigger, Auto trigger mode, 0V level, channel 1 source, DC coupling, rising edge slope,

20ns holdoff time.

l Display - Persistence off, 50% grid intensity, 80% waveform intensity, 80% screen brightness.

l Other - Acquire mode normal, [Run/Stop] to Run, cursors, and measurements off.

l Labels - All custom labels that you have created are erased, and all channel labels will be set to their

original names.

WisdomAugust

Input a Waveform

The first signal to input to the oscilloscope is the probe comp (2Vpp@1KHz square) signal. This signal

is used for compensating probes.

1 Connect an oscilloscope probe from channel 1 to the probe comp terminal on the front panel.

2 Connect the probe’s ground lead to the ground terminal (next to the probe comp terminal).

WisdomAugust

Defeating the ground connection and floating the oscilloscope chassis will probably result in inaccurate

measurements and may also cause equipment damage. The probe ground lead is connected to the

oscilloscope chassis and the ground wire in the power cord. If you need to measure between two live

points, use a differential probe with a sufficient dynamic range.

WARNING Do not negate the protective action of the ground connection to the oscilloscope.

The oscilloscope must remain grounded through its power cord. Defeating the ground create

an electric shock hazard.

WisdomAugust

Getting Started

Connect Probes to the Oscilloscope

1 Connect the oscilloscope probe to an oscilloscope channel BNC connector.

2 Connect the probe’s retractable hook tip to the point of the interest on the circuit or device under test.

Be sure to connect the probe ground lead to a ground point on the circuit.

CAUTION When measuring voltages over 80V, use a 10:1 probe.

CAUTION Do not float the oscilloscope chassis

WisdomAugust

WisdomAugust

Inspect the package contents including the following items.

? MPO6002EDU Series oscilloscope.

? Power cord.

? BNC cable.

? Oscilloscope probes.

? Test Leads with BNC plug and alligator clip.

? BNC to BNC cable.

? Type C cables.

? Digital probes.

? Mini test hooks.

WisdomAugust

? Math waveforms: add, substract, multiply, divide, FFT, integrate, Differentiate, square root, expression.

? Event search function.

? Frequency response analyzer (FRA).

? With Pass/Fail output and Trigger out function.

? 5 bits digital voltmeter (DVM) and 6 bits frequecy counter.

? Built-in 16 digital channels logic analyzer lets you debug mixed signal designs using analog signals and tightly correlated digital signals simultaneously.

? Built-in 3 channels waveform generator with: sine, square, ramp, noise, pulse, DC, sine cardinal, exponential fall, haversine, lorentz, dual tone, gause, ECG, arbitrary.

? Standard interfaces: USB Device, USB Host, LAN, AUX port and WiFi module.

? Optional interfaces: HDMI.

? Supports remote command control.