Electronic Engineer Discuss

View: 8271|Reply: 7
Print Prev. thread Next thread

How to use the Digital Generator on the waveform generator of HDG6000B?

[Copy link]

58

Threads

1266

Posts

1346

Credits

金牌会员

Rank: 6Rank: 6

Credits
1346
Jump to specified page
1#
Post time 2019-6-10 08:03:05 | Show the author posts only Reply Awards |Descending |Read mode


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x
Reply

Use magic Report

58

Threads

1266

Posts

1346

Credits

金牌会员

Rank: 6Rank: 6

Credits
1346
2#
 Author| Post time 2019-6-11 08:10:50 | Show the author posts only
Review the Output Terminal
                           
Signal Output Terminal Under Device Display




Output Terminal On Digital Generator Interface




Terminal Description



Note: Vcc: 3.3V


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1266

Posts

1346

Credits

金牌会员

Rank: 6Rank: 6

Credits
1346
3#
 Author| Post time 2019-6-12 08:15:44 | Show the author posts only
Edited by WisdomAugust at 2019-6-13 13:11

Press Data Output key to enable digital generator function.
The backlight of the key become light in yellow.

The digital generator interface is opened and output the signal at the same time.

Digital Generator Interface



Signal Display on Logic Analyzer



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1266

Posts

1346

Credits

金牌会员

Rank: 6Rank: 6

Credits
1346
4#
 Author| Post time 2019-6-13 13:15:04 | Show the author posts only
Press Function softkey to set the function as sync signal, programmable signal and turn off function.

When select function as Sync, the digital generator output synchronized signal of CH1 or CH2.


When select the sync signal source to CH1


When select the sync signal source to CH2


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1266

Posts

1346

Credits

金牌会员

Rank: 6Rank: 6

Credits
1346
5#
 Author| Post time 2019-6-14 08:03:08 | Show the author posts only
Open CH1 waveform output, Select the Signal Type to "Sine ", frequency to “1KHz”,
Amplitude to 1V, Y Offset to 0V.



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1266

Posts

1346

Credits

金牌会员

Rank: 6Rank: 6

Credits
1346
6#
 Author| Post time 2019-6-17 08:01:07 | Show the author posts only
Connect Digital Generator Terminals to LOGIC Analyzer Terminals to measure. The output signal of
D0-D15 terminals is a square waveform (3.3V, peak- to- peak).



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1266

Posts

1346

Credits

金牌会员

Rank: 6Rank: 6

Credits
1346
7#
 Author| Post time 2019-6-18 08:11:47 | Show the author posts only
Programmable Signal
Select function to Prog, use the direction keys and
knob   to modify the value for D0~D15 to 0 or 1.


Programmable Signal: Users can edit digital signal.



This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x

58

Threads

1266

Posts

1346

Credits

金牌会员

Rank: 6Rank: 6

Credits
1346
8#
 Author| Post time 2019-6-19 08:53:26 | Show the author posts only
The corresponding terminals will output high level or low level. When the data is set to 0, the corresponding
output voltage is 0V.
When the data is set to 1, the corresponding output voltage is 3.3V.
Such as, D0~D7: 10101010, D8~D15: 01010101, in the figure below.
Programmable Signal D0~D7: 10101010, D8~D15: 01010101 Display on Generator

Programmable Signal D0~D7: 10101010, D8~D15: 01010101 Display on Logic Analyzer


This post contains more resources

You have to Login for download or view attachment(s). No Account? Register

x
You have to log in before you can reply Login | Register

Points Rules

Dark room|Mobile|Archiver|Electronic Engineer Discuss

2024-4-20 03:04 GMT+8 , Processed in 0.158316 second(s), 21 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.

Quick Reply To Top Return to the list