MPO6002EDU Series Oscilloscope Guide

WisdomAugust

Math Key -> Operator -> d/dt -> Settings Softkey help information

When d/dt selected, press this softkey to open the Differential Settings Menu.

Math Key -> Operator -> d/dt -> Settings -> Step Softkey help information

The Step softkey sets the differential interval.

Math Key -> Operator -> Expression -> Settings Softkey help information

When Expression selected, press this softkey to open the Expression Settings Menu.

Math Key -> Operator -> Expression -> Settings -> Edit Softkey help information

Press this softkey to display the Edit Expression Virtual Keypad on the screen. Then, use the V0 knob or touch

gestures (if touch screen enabled) to edit your math waveform expressions that incorporate active waveforms,

measurements and numeric constants, and press Enter key on the keypad to create an expression.

WisdomAugust

Math Key -> Operator -> Expression -> Settings -> CH1 Bias Softkey help information

Press this softkey and turn the V0 knob to adjust the bias of channel 1.

Math Key -> Operator -> Expression -> Settings -> CH2 Bias Softkey help information

Press this softkey and turn the V0 knob to adjust the bias of channel 2.

Math Key -> Operator -> Expression -> Settings -> CH3 Bias Softkey help information

Press this softkey and turn the V0 knob to adjust the bias of channel 3.

Math Key -> Operator -> Expression -> Settings -> CH4 Bias Softkey help information

Press this softkey and turn the V0 knob to adjust the bias of channel 4.

WisdomAugust

Math Key -> Operator -> Expression -> Settings -> CH1 Thres Softkey help information

Press this softkey to toggle between CH1 Threshold and CH1 Threshold Fine adjustment, and use the V0 knob

to adjust the threshold of channel 1.

Math Key -> Operator -> Expression -> Settings -> CH2 Thres Softkey help information

Press this softkey to toggle between CH1 Threshold and CH2 Threshold Fine adjustment, and use the V0 knob

to adjust the threshold of channel 2.

Math Key -> Operator -> Expression -> Settings -> CH3 Thres Softkey help information

Press this softkey to toggle between CH1 Threshold and CH3 Threshold Fine adjustment, and use the V0 knob

to adjust the threshold of channel 3.

Math Key -> Operator -> Expression -> Settings -> CH4 Thres Softkey help information

Press this softkey to toggle between CH1 Threshold and CH4 Threshold Fine adjustment, and use the V0 knob

to adjust the threshold of channel 4.

WisdomAugust

Math Key -> Operator -> Expression -> Settings -> Return Softkey help information

Press this softkey to return to the previous menu.

Math Key -> Offset Softkey help information

Press this softkey and turn the V0 knob to adjust the vertical offset of the math operation result.

Push the V0 knob to zero the offset.

Math Key -> Scale Softkey help information

Press this softkey and turn the V0 knob to adjust the vertical scale of the math operation result.

Math Key -> Operator -> FFT -> Source Softkey help information

Select channel as the FFT source.

Math Key -> Operator -> FFT -> Center Softkey help information

Sets the desired FFT frequency at the center vertical grid line of the display.

WisdomAugust

Math Key -> Operator -> FFT -> Span Softkey help information

Press Span softkey and rotate the V0 knob to set the desired frequency range that represented by the width of the display.

Math Key -> Operator -> FFT -> Ref Level Softkey help information

Press this softkey and turn the V0 knob to adjust the vertical offset.

Push the V0 knob to zero the offset.

Math Key -> Operator -> FFT -> Scale Softkey help information

Press this softkey and rotate the V0 knob to adjust the vertical scale of the operation result in 1-2-5 step sequence.

Math Key -> Operator -> FFT -> Vertical Units Softkey help information

Sets the FFT vertical scale unit to dB or VRMS.

BHUBESH25

Date and time reset on turning off. How to resolve.

BHUBESH25

I am getting maximum of 80Mpts on oscilloscope at 1GSa/s

WisdomAugust

BHUBESH25 replied at 2021-8-12 06:51
Date and time reset on turning off. How to resolve.

Try to replace a new cell battery on the mother board.

WisdomAugust

Math Key -> Operator -> FFT -> Window Softkey help information

Applies a window to the FFT input signal.

* Rectangular - Best frequency resolution but worst amplitude accuracy. Excellent to measure a transient

signal where the signal levels before and after the event are nearly the same.

* Hanning - Good frequency resolution, low spectral leakage, and fair amplitude accuracy. Useful for measuring

transients or bursts where the signal levels are significantly different before and after the event.

* Hamming - Better frequency resolution, moderate spectral leakage, and fair amplitude accuracy. Suitable to

look at sine, periodic, and narrow bank spectral noise.

* Blackman - Worst frequency resolution, low spectral leakage, and good amplitude accuracy. Mainly to measure

single frequency signal to detect higher-order harmonics.

* Bartlett - Similar to Hanning but with higher and wider secondary lobes. Good to measure the narrowband signals

with strong noise interference.

* Flattop - With highest amplitude flatness. Used to make accurate amplitude measurements of frequency peak.

WisdomAugust

Math Key -> Operator -> FFT -> FFT Only Softkey help information

Selects to display both the source waveform and the FFT waveform together, or to display the FFT waveform

only.

Math Key -> Operator -> FFT -> AutoScale Softkey help information

Adjusts the FFT frequency Center and Span to the optimal values in order to display the entire available

spectrum.

V0 Knob help information

The V0 knob is a multifunction knob, used to select items from menus and input values. Its function changes

when a different menu is displayed.

Its indicator lights up when this knob is active and can be used to select a value.

Turning the knob will move the selection cursor up or down, and push the knob will select the item.

On the pop-up keyboard, turn the knob to select the desired letter or number, and then push the knob to

select the value to add to the input.