Trig Menu Key -> Type -> Setup/Hold -> Source Softkey help informationSelects data signal source of the setup and hold trigger from analog channels.
Trig Menu Key -> Type -> Setup/Hold -> SDA Softkey help informationSelects data signal source of the setup and hold trigger from analog channels.
Trig Menu Key -> Type -> Setup/Hold -> Data Type Softkey help informationPress this softkey to toggle the data signal's effective pattern between high level and low level.
Trig Menu Key -> Type -> Setup/Hold -> SCL Softkey help informationSets clock signal source of the setup and hold trigger to any analog or digital channel input.
Trig Menu Key -> Type -> Setup/Hold -> Slope Softkey help informationThis softkey sets the active edge of the clock signal to rising or falling.
Trig Menu Key -> Type -> Setup/Hold -> Type Softkey help informationPress this softkey to toggle the time type between setup and hold.
Trig Menu Key -> Type -> Setup/Hold -> When Softkey help informationThe scope triggers when the setup time or hold time is smaller than the preset time.
Trig Menu Key -> Type -> Setup/Hold -> Width Softkey help informationPress this softkey and use the V0 knob to preset the time. Settings range: 8ns - 10s.
Trig Menu Key -> Type -> UART/LIN/CAN -> Source Softkey help informationPress this softkey and turn the V0 knob to select the trigger source from analog or digital channels input.
Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> Baud Rate Softkey help informationThis softkey selects a baud rate of data transmission to match the signal in the device under test. If the desired baud rate is not listed, select User Defined.
Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> User Baud Softkey help informationWhen User Defined selected on the Baud Rate softkey, press User Baud softkey and turn the V0 knob to set the desired baud rate at a small step of 1 bps.
Trig Menu Key -> Type -> UART -> When Softkey help informationPress this softkey to select the desired trigger condition. * Start -the scope triggers on the start frame position.* Stop -the scope triggers on the stop frame position. The trigger will occur on the first stop bit whether the device under test uses 1, 1.5, or 2 stop bits. * Data - triggers on the last bit of the specified data bits. * Parity Error - triggers on a parity error based on the preset parity on the Parity softkey.* Error - triggers when an error occurs by checking the start bit and stop bit.
Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> Idle Level Softkey help informationSet idle level to high or low to match the state of the device under test when at idle.
Trig Menu Key -> Type -> UART -> Polarity Softkey help informationAccording to the device under test to select the parity from odd, even, or none.
Trig Menu Key -> Type -> UART -> Data Bits Softkey help information This softkey sets the number of bits to 5, 6, 7, or 8bits in the UART words to match the device under test.
Trig Menu Key -> Type -> UART -> Data Softkey help information This softkey sets the trigger data ( only available when the trigger type is data).
Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> Decode Softkey help information Press this softkey to enable or disable the decode display.
Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> Position Softkey help information If the decode turned on, press this softkey and use the V0 knob to move the decode label up and down on the display.
Trig Menu Key -> Type -> UART/LIN/CAN/SPI/IIC -> Event Table Softkey help information Press this softkey to open the Event Table Menu and display the Decoded Packet Data Tabular on the screen.
Trig Menu Key -> Type -> LIN -> When Softkey help informationPress this softkey to select the desired trigger condition. * Break Field -the scope triggers on the edge at the Sync Break exit of the LIN single-wire bus signal that marks the beginning of the message frame.* Sync Field -the scope triggers on the last bit of the sync field.* ID Field -the scope triggers on the last bit of the identifier field.* Sync Error - triggers when the synchronous data is not 0x55.* Identifier - triggers on a specific identifier.* ID & Data - triggers on a combination of both identifier and data.
Trig Menu Key -> Type -> LIN/CAN -> Identifier Softkey help informationPress this softkey and use the V0 knob to setup the identifier value.
Trig Menu Key -> Type -> LIN/CAN/IIC -> Data 1 Softkey help informationPress this softkey and turn the V0 knob to set the data value for Data 1.
Trig Menu Key -> Type -> LIN/CAN/IIC -> Data 2 Softkey help informationPress this softkey and turn the V0 knob to set the data value for Data 2.
Trig Menu Key -> Type -> LIN/CAN/IIC -> Data 3 Softkey help informationPress this softkey and turn the V0 knob to set the data value for Data 3.
Trig Menu Key -> Type -> LIN/CAN/IIC -> Data 4 Softkey help informationPress this softkey and turn the V0 knob to set the data value for Data 4.
Trig Menu Key -> Type -> CAN -> When Softkey help informationPress this softkey to select the desired trigger condition. * Start or Frame -triggers at the start of a frame.* Remote Frame ID - triggers on remote frames with the preset identifier.* Data Frame ID - triggers on data frames matchingthe preset identifier. * Frame ID - triggers on remote or data frames matching the preset identifier. * Data Frame ID & Data - triggers on data framesmatching the preset identifier and data.* Error Frame - triggers on the error frame.* All Errors - triggers on any form error or active error.* Ack Error - triggers on the recessive acknowledge bit.* Overload Frame - triggers on CAN overload frames.
Trig Menu Key -> Type -> SPI -> SCL Softkey help informationThis softkey sets the source of the serial clock signal to any analog or digital channel.
Trig Menu Key -> Type -> SPI -> Slope Softkey help informationYou can use this Slope softkey to select the clock edge between rising and falling.
Trig Menu Key -> Type -> SPI -> SDA Softkey help informationPress this softkey to set the source of the serial data signal to any analog or digital channel.
Trig Menu Key -> Type -> SPI -> Timeout Softkey help informationThe scope searches for the data on which to trigger after a specified period of time during which the clock signal stays in the idle state.Press this softkey and rotate the V0 knob to adjust the Timeout. Time setting range: 8ns - 10s.
Trig Menu Key -> Type -> SPI -> Data Length Softkey help informationThis softkey sets the number of bits in the serial data string from 4 bits to 32 bits.
Trig Menu Key -> Type -> SPI -> Data Bit Softkey help informationPress this softkey and turn the V0 knob to select the number of bits in a word.
Trig Menu Key -> Type -> IIC -> Address Size Softkey help informationPress this softkey to set the scope to trigger on a 7- bit address read/write frame or a 10-bit address write frame.
Trig Menu Key -> Type -> IIC -> SCL Softkey help informationThis softkey sets the source of the serial clock signal to any analog or digital channel input.
Trig Menu Key -> Type -> IIC -> SDA Softkey help informationPress this softkey to set the source of the serial data signal to any analog or digital channel input.
Trig Menu Key -> Type -> IIC -> When Softkey help informationPress this softkey to select the desired trigger condition. * Start - triggers when serial data transitions from high to low while serial clock is high level.* Stop -triggers when serial data transitions from low to high level while serial clock is high.* No Ack - triggers when a write data byte or the selected address field is not acknowledged.* Address - triggers on the specified address value. * Restart - triggers when another start condition occurs before a stop condition.* Address & Data - triggers on a combination of both specified address and data.
Trig Menu Key -> Type -> IIC -> Address Softkey help informationPress this softkey and use the V0 knob to set a address value.