Utility Key -> Pass/Fail -> Output to DDS Softkey help informationWhen turning on the output to DDS, the scope is able to output a negative pulse train from the Gen Out terminal.
Utility Key -> Pass/Fail -> Return Softkey help informationPress this softkey to return to the previous menu.
Utility Key -> System Set Softkey help informationThis key opens the System Setup Menu where you can turn on or off the sound, set network, edit time and date, and perform touch panel calibration.
Utility Key -> System Set -> Sound Softkey help informationTurn on or off the sound of pressing keys.
Utility Key -> System Set -> Network Softkey help informationPress this softkey to open the Network Setup Menu.
Edited by WisdomAugust at 2021-1-4 09:40
Utility Key -> System Set -> Network -> Network Softkey help informationToggle the network type between eth0 and wlan0.
Utility Key -> System Set -> Network -> Status On/Off Softkey help informationTurn on or off the network status.
Utility Key -> System Set -> Network -> DHCP On/Off Softkey help informationTurn on or off DHCP (Dynamic Host Configuration Protocol).
Utility Key -> System Set -> Network -> Auto IP On/Off Softkey help informationEnable or disable the Auto IP.
Utility Key -> System Set -> Network -> Confirm Softkey help informationConfirm your settings of the network menu page one.
Utility Key -> System Set -> Network -> IP Add Softkey help informationConfigure the IP address.
Utility Key -> System Set -> Network -> Subnet Mask Softkey help informationConfigure the IP Subnet Mask.
Edited by WisdomAugust at 2021-1-5 08:38
Utility Key -> System Set -> Network -> Gateway Softkey help informationConfigure Gateway.
Utility Key -> System Set -> Network -> DNS Softkey help informationConfigure DNS (Domain Name System).
Utility Key -> System Set -> Network -> Confirm Softkey help informationConfirm your settings of the network menu page two.
Utility Key -> System Set -> Network -> Hotspot Softkey help informationPress this softkey to enable the Hotspot Settings. The scope will automatically search for available hot spots nearby. And SSID and PSK become active to be set.
Utility Key -> System Set -> Network -> Scan Result Softkey help informationDisplay searched nearby Wi-Fi hotspots.
Utility Key -> System Set -> Network -> SSID Softkey help informationConfigure SSID (Service Set Identifier).
Utility Key -> System Set -> Network -> PSK Softkey help informationConfigure PSK (Pre Shared Key).
Utility Key -> System Set -> Network -> Confirm Softkey help informationConfirm your settings of the network menu page three.
Edited by WisdomAugust at 2021-1-6 08:28
Utility Key -> System Set -> Network -> Mac Add Softkey help informationConfigure MAC address.
Utility Key -> System Set -> Network -> Service Softkey help informationSwitch the network protocol between TCP (Transmission Control Protocol) and HTTP (HyperText Transfer Protocol).
Utility Key -> System Set -> Network -> Return Softkey help informationPress this softkey to return to the previous menu.
Utility Key -> System Set -> Date&Time Softkey help informationPress this softkey to enter the Time Setup Menu.
Utility Key -> System Set -> Date&Time -> Year Softkey help informationPress this softkey and turn V0 knob to adjust correct year.
Utility Key -> System Set -> Date&Time -> Month Softkey help informationPress this softkey and turn V0 knob to adjust correct month.
Utility Key -> System Set -> Date&Time -> Day Softkey help informationPress this softkey and turn V0 knob to adjust correct day.
Utility Key -> System Set -> Date&Time -> Hour Softkey help informationPress this softkey and turn V0 knob to adjust correct hour.
Utility Key -> System Set -> Date&Time -> Minute Softkey help informationPress this softkey and turn V0 knob to adjust correct minute.
Utility Key -> System Set -> Date&Time -> Second Softkey help informationPress this softkey and turn V0 knob to adjust correct second.
Utility Key -> System Set -> Date&Time -> Return Softkey help informationPress this softkey to return to the previous menu.
Utility Key -> System Set -> TP Cal Softkey help informationTo perform calibration of the touch panel.
Utility Key -> System Set -> Return Softkey help informationPress this softkey to return to the previous menu.
Utility Key -> Self Cal Softkey help informationRunning the self-calibration routine to optimize the signal path in scope for top measurement accuracy.Allow the temperature of the scope to warm up and disconnect all inputs and outputs before performing the self-calibration.Self-calibration can be run any time the operating the temperature of the scope changes by more than 5℃.
Utility Key -> Self Cal -> Self Cal Softkey help informationPress this softkey to begin the user's self-calibration.
Utility Key -> Self Cal -> Cancel Softkey help informationPress this softkey to exit the user's self-calibration mode.
Utility Key -> Self Cal -> Return Softkey help informationPress this softkey to return to the previous menu.
Utility Key -> History Wave Softkey help informationYou can use the History Waveform Mode to scroll back in time to isolate anomalies or other waveform events.It automatically saves all acquisitions until the scope's history buffer full and stopping the trigger and displaying a list of previously captured waveforms.
Utility Key -> Hardware Self-Test Softkey help informationPerform the self-test (a series of internal procedures) to verify the scope is operating properly.
Utility Key -> Front-Panel Self-Test Softkey help informationPress this key to perform a front panel keys, knobs, LEDs, and display test.
Utility Key -> Potter Diagram Softkey help informationTurn on or off frequency response analysis (FRA).
Edited by WisdomAugust at 2021-1-12 08:05
Utility Key -> Potter Diagram -> Enable Softkey help informationPress this softkey to display the Frequency Response Analysis chart.
Utility Key -> Potter Diagram -> SetUp Softkey help informationEnter the test parameters settings menu to set up source, frequency, and amplitude.
Utility Key -> Potter Diagram -> SetUp -> Input Source Softkey help informationSelect the input source channel.
Utility Key -> Potter Diagram -> SetUp -> Output Source Softkey help informationSelect the output source channel.
Utility Key -> Potter Diagram -> SetUp -> Freq Start Softkey help informationSet up the start frequency.
Utility Key -> Potter Diagram -> SetUp -> Freq Stop Softkey help informationSet up the stop frequency.
Utility Key -> Potter Diagram -> SetUp -> Amplitude Softkey help informationSet up the amplitude of the waveform generator.Press this softkey to toggle between amplitude fine and amplitude coarse. And use V0 knob to adjust the waveform generator’s amplitude.
Utility Key -> Potter Diagram -> SetUp -> Return Softkey help informationPress this softkey to return to the previous menu.
Utility Key -> Potter Diagram -> Chart Softkey help informationDisplay the test parameters settings menu to set up the gain and phase.
Utility Key -> Potter Diagram -> Chart -> Gain Scale Softkey help informationPress this softkey and turn V0 knob to adjust the gain scale (dB).
Utility Key -> Potter Diagram -> Chart -> Gain Offset Softkey help informationPress this softkey and turn V0 knob to adjust the gain deviation (dB).
Utility Key -> Potter Diagram -> Chart -> Phase Scale Softkey help informationPress this softkey and turn V0 knob to adjust the phase scale (degree).
Utility Key -> Potter Diagram -> Chart -> Phase Offset Softkey help informationPress this softkey and turn V0 knob to adjust the phase deviation (degree).
Utility Key -> Potter Diagram -> Chart -> Return Softkey help informationPress this softkey to return to the previous menu.
Utility Key -> Potter Diagram -> Run Softkey help informationPress this softkey to begin the frequency response test.
Utility Key -> Potter Diagram -> Run -> Cancel Softkey help informationPress this softkey to exit the frequency response test.
Utility Key -> Potter Diagram -> Press To Save Softkey help informationWhen the scope complete the frequency response test, press this softkey to open the File Manager Menu if a USB storage device has been detected.
Utility Key -> Potter Diagram -> Press To Save -> New Softkey help informationPress this softkey to enter New File Menu and display the alpha-numeric keypad dialog.
Utility Key -> Potter Diagram -> Press To Save -> New -> Type Softkey help informationSelect a file or a directory to create.
Utility Key -> Potter Diagram -> Press To Save -> New -> Switch To Softkey help informationToggle between Name and Keypad.
Utility Key -> Potter Diagram -> Press To Save -> New -> Backspace Softkey help informationDeletes a character from the name each time before the cursor's left.
Utility Key -> Potter Diagram -> Press To Save -> New -> Delete Softkey help informationClear all characters for the name.
Utility Key -> Potter Diagram -> Press To Save -> New -> Save Softkey help informationCreate new a file or a directory on the USB storage device.
Utility Key -> Potter Diagram -> Press To Save -> New -> Return Softkey help informationPress this softkey to return to the previous menu.
Utility Key -> Potter Diagram -> Press To Save -> Delete Softkey help informationTo remove the selected file.